Tips & Tutorial

Cari Tahu Cara Mengganti Power Supply Pada Mac Mini Late 2014

Pada kesempatan kali ini, saya akan menjelaskan tentang Cara Mengganti Power Supply Pada Mac Mini Late 2014 yang berasal dari www.ifixit.com.

Ada sekitar 30 Langkah Cara Mengganti Power Supply Pada Mac Mini Late 2014.

Mac Mini Cover

Step 1 — Bottom Cover
The bottom cover is clipped onto three screw posts.
Pry near, but not right on the screw posts.
Step 2
Use the plastic opening tool to pry the bottom cover up off of the Mac Mini.
Step 3
Lift and remove the bottom cover.
Step 4 — Antenna Plate
Remove the following TR6 screws from the antenna plate:
Three 4.1 mm screws
Three 1.9 mm screws
Step 5
Do not completely remove the antenna plate; it is still connected to the Mac Mini by an antenna cable.
With the I/O ports facing you, flip the antenna plate to the right to allow access to the antenna cable connector.
Step 6
Remove the single 3.4 mm T6 screw and washer from the antenna cable.
Be careful not to lose the washer when removing the screw.
Step 7
Use the point of a spudger to lift the antenna connector straight up off its socket on the airport card.
Step 8
Carefully pull the antenna cable out from the gap between the power supply and case.
Step 9
Remove the antenna plate from the Mac Mini.

Power Supply Mac Mini Step 9
Step 10 — Fan Assembly
Remove the two 12 mm T6 screws from the fan.
Loosen the 27 mm T6 captive screw.
Step 11
The fan connector is trapped under the edge of the fan and cannot be disconnected until the fan is moved.
Do not attempt to remove the fan entirely.
Lift the fan straight up to free the captive screw from its hole in the logic board.
Pull the fan away from the SSD until you can easily access the fan connector.
Step 12
Use the point of a sudger to lift the fan connector straight up out of its socket on the logic board.
Step 13
Remove the fan from the Mac Mini.
Step 14 — Logic Board Assembly
Remove the 2.6 mm T6 screw securing the SATA cable connector bracket.
Step 15
Remove the SATA cable connector bracket.
Step 16
Use the flat end of a spudger to lift the SATA cable connector up off of its socket on the logic board.
Step 17
Use the tip of a spudger to disconnect the IR sensor cable connector by prying it straight up from its socket.
Step 18
Remove the two 2.6 mm T6 screws securing the PCIe SSD cable bracket.
Step 19
Remove the PCIe SSD cable bracket.
Step 20
Lift the PCIe SSD connector up off its socket.
Step 21
Remove the single 16 mm T6 screw securing the logic board.
Step 22
To remove the logic board, the two cylindrical rods of the Mac Mini Logic Board Removal Tool must be inserted into the holes highlighted in red. Inserting instruments into any logic board holes other than the ones highlighted in red may destroy the logic board.
Insert the Mac Mini Logic Board Removal Tool into the two holes highlighted in red. Be sure the rods make contact with the case under the logic board before proceeding.
Step 23
Carefully pull the tool toward the I/O board. The logic board and I/O board assembly should slightly slide out of the outer case.
Cease prying when the removal tool makes contact with the opening in the rear case.
Remove the Mac Mini Logic Board Removal tool.
Step 24
Pull the DC-In cable connector straight out of its socket on the logic board.
Step 25
Carefully slide the logic board assembly out of the Mac Mini, minding any cables that may get caught.
Step 26 — Power Supply
The AC-in socket is secured with a small metal retaining clip.
Use tweezers or your fingers to pull the clip away from the AC-in socket, and remove it from the Mac Mini.
When replacing the clip, push it in until it stops—it should be secure even if there is no audible click.
Step 27
To free the power supply from the case, grab the AC-In connector, which acts like a latch.
Rotate the AC-In connector 90 degrees counter-clockwise.
Step 28
The AC-In latch should fit into the groove above it in the case.
During reassembly ensure the power supply is inserted far enough into the case that the latch will engage with the groove.
Step 29
Remove the 8 mm T6 screw securing the power supply.
Step 30
Slide the power supply out of the Mini, minding any cables that may get caught.

Power Supply Mac Mini

Untuk langkah lebih lengkapnya yang disertai gambar bisa langsung kunjungi www.ifixit.com.
Semoga informasi mengenai Tutorial Cara Mengganti Power Supply Pada Mac Mini Late 2014 tersebut dapat menambah wawasan anda dan bisa menjadikan anda teknisi hardware Apple yang handal.

Apabila anda memiliki informasi tambahan, jangan sungkan untuk berkomentar di kolom komentar yang berada di bagian bawah artikel ini.

 

 

Sumber : www.ifixit.com

Jasa servis imac

Click to comment

You must be logged in to post a comment Login

Flash

Copyright © 2014 - 2017 klikmac

To Top