Tips & Tutorial

iPhone 6 Plus Anda tidak bisa bergetar? Yuk Ikuti Langkah-Langkah Memperbaiki Vibrator Pada iPhone 6 Plus

klikmac – Apakah anda pernah mengalami iPhone 6 Plus anda tidak bisa bergetar?

Pada kesempatan kali ini, saya akan menjelaskan tentang Cara Memperbaiki Vibrator pada iPhone 6 Plus yang berasal dari www.ifixit.com.

Ada sekitar 23 Langkah Cara Memperbaiki Vibrator pada iPhone 6 Plus.

Yuk kita cermati setiap langkah-langkahnya :

iPhone 6 PLUS

Step 1 — Pentalobe Screws
Power off your iPhone before beginning disassembly.
Remove the two 3.6 mm Pentalobe screws next to the Lightning connector.

Step 2 — iSclack Opening Procedure
The next two steps demonstrate using the iSclack, a great tool for safely opening the iPhone 6 Plus that we recommend for anyone doing more than one repair. If you aren’t using the iSclack, skip to Step 4.
If the plastic depth gauge is attached at the center of the iSclack, remove it now—it’s not needed for larger phones like the iPhone 6 Plus.
Close the handle on the iSclack, opening the suction cup jaws.
Place the bottom of your iPhone in between the suction cups.
Position the iSclack’s upper suction cup against the display, near the home button.
Open the handles to close the jaws of the iSclack. Center the suction cups and press them firmly onto the top and bottom of the iPhone.

Step 3
Hold onto your iPhone securely and close the handle of the iSclack to separate the suction cups, pulling the front panel up from the rear case.
The iSclack is designed to safely open your iPhone enough to separate the pieces, but not enough to damage any of the display cables.
Peel the two suction cups off your iPhone.
Skip the next three steps and continue on Step 7.

Step 4 — Front Panel Assembly
If you don’t have an iSclack, use a single suction cup to lift the front panel:
Press a suction cup onto the screen, just above the home button.
Be sure the cup is pressed securely onto the screen to get a tight seal.

Step 5
While holding the iPhone down with one hand, pull up on the suction cup to slightly separate the front panel assembly from the rear case.
Take your time and apply firm, constant force. The display assembly is a much tighter fit than most devices.
Using a plastic opening tool, begin to gently pry the rear case down, away from the display assembly, while continuing to pull up with the suction cup.
There are several clips attaching the front panel assembly to the rear case, so you may need to use a combination of the suction cup and plastic opening tool to free the front panel assembly.

Step 6
Pull the plastic nub to release the vacuum seal on the suction cup.
Remove the suction cup from the display assembly.

Step 7
Pull the home button end of the front panel assembly away from the rear case, using the top of the phone as a hinge.
During the next few steps, until you remove the front panel assembly, keep it supported at a 90º angle in relation to the rear case.

Step 8
Several clips along the top edge of the front panel form a partial hinge, allowing the front panel assembly to swing open like a book.
During reassembly, align the clips just below the top edge of the rear case. Then, slide the front panel upward until its top edge is flush with that of the rear case.

Step 9
While holding the front panel open at about a 90º angle, remove the following screws securing the front panel assembly cable bracket:
Three 1.2 mm Phillips #00 screws
One 1.5 mm Phillips #00 screw
One 2.9 mm Phillips #00 screw

Step 10
Remove the front panel assembly cable bracket from the logic board.

Step 11
In the next four steps, take care to pry up only on the cable connectors, and not on their sockets on the logic board.
While still supporting the front panel, use a plastic opening tool to disconnect the front-facing camera and earpiece speaker cable connector.

Step 12
Use a plastic opening tool to disconnect the home button cable connector.

Step 13
Use a plastic opening tool to disconnect the digitizer cable connector.

Step 14
Finally, use a plastic opening tool to disconnect the display data cable connector.
When reassembling your phone, the display data cable may pop off the connector. This can result in white lines or a blank screen when powering your phone back on. If that happens, simply reconnect the cable and power cycle your phone. The best way to power cycle your phone is to disconnect and reconnect the battery connector.

Step 15
Remove the front panel assembly from the rear case.

Step 16 — Battery Connector
Remove the following screws from the battery connector bracket:
One 2.3 mm Phillips #00 screw
One 3.1 mm Phillips #00 screw

Step 17
Remove the metal battery connector bracket from the iPhone.

Step 18
Use a plastic opening tool to gently pry the battery connector up from its socket on the logic board.
Take care to only pry up on the battery connector, and not the socket on the logic board. If you pry up on the logic board socket, you may break the connector entirely.

Step 19 — Vibrator
Pry the vibrator connector cable up from its socket on the logic board with the flat end of a spudger.

Step 20
Use the tip of a spudger to disconnect the interconnect antenna cable from its socket on the logic board.

Step 21
Grasp the interconnect antenna cable with a pair of tweezers and carefully de-route it from its channel on the vibrator assembly.

Step 22
Remove the two 2.5 mm Phillips #00 screws securing the vibrator to the rear case.

Step 23
Remove the vibrator from the iPhone.

vibrator iPhone 6+

Untuk langkah lebih lengkapnya yang disertai gambar bisa langsung kunjungi www.ifixit.com.

Semoga informasi mengenai Tutorial Memperbaiki Vibrator Pada iPhone 6 Plus tersebut dapat menambah wawasan anda dan bisa menjadikan anda teknisi hardware iPhone 6 Plus yang handal.

Apabila anda memiliki informasi tambahan, jangan sungkan untuk berkomentar di kolom komentar yang berada di bagian bawah artikel ini.

Sumber : www.ifixit.com

Click to comment

You must be logged in to post a comment Login

Flash

Copyright © 2014 - 2017 klikmac

To Top